Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:

! ?! L. y/ @, ^0 M1 U
1 N5 B' \0 @* S! mCould not connect to socket 9189 on host localhost
2 P) O! R( n( z3 I3 e" |  i
Probable causes:

1: The viewer is not running, or
) v% o, q2 M2 G8 d! ?3 D2: The viewer's server socket is not activated
: a: U! E$ ^* d0 g+ L
) {; g5 t, y- a3 n6 h( f; F
請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
/ t4 P# r+ g. r. G6 M' k所以你無法將RVE的資料傳回layout
  q0 {+ R. K& ?! g* [* Nvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
0 g+ F8 c7 W" {( e1 r那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
$ Y! ~. `6 M, \virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

: K1 Y; B2 N7 B2 d& C

我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
& K( a; O0 ^7 i  q4 G( i& \, L0 x                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
) Z6 N7 P8 z$ e+ SIf you invoke Calibre Interactive from a layout or schematic viewer, communication between
/ ^9 R+ D; j& H5 V( B6 L( X% Q" q1 O4 y7 u" `the two applications is set up automatically. If you open a viewer after invoking Calibre
- M' z) e+ @2 ]5 DInteractive, you can set up communication between the two tools through IPC sockets.
* X. w& R/ H0 z5 e: wBy default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
You can change the socket address used by following this procedure:
5 k& s5 s$ @3 w/ v+ r% O3 z+ c1. Open the viewer.
2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
* E6 }2 L( H! S1 C& A3. In Calibre Interactive, choose Setup > Layout Viewer…
4. Enter the socket number that you activated in the viewer.
5. Click Connect.
* h9 w- e3 B/ L6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
) P4 Z; R- j0 M& u/ fthe two applications is set up automatically. If you open a viewer a ...

( w( z# y. c$ @, ^% Q# [
9 E& j  b1 ~9 j8 Z( {1 U
一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
- w2 S! p5 k) d* d它的socket number 有相同嗎?