要trace layout上的power line?

camilla

各位前輩,
$ R8 Z4 [! b  W0 Z' Y
- v9 J! U; N- q4 _6 }   我實驗室是使用.18um 1p3m的製程。 學長今天出了一道問題給我,
要我寫一個command file去把layout裡的vdd全抓出來,方便他檢查
  C: {. L5 f, K  S6 z/ A我畫的layout,但在有轉層的地方,不要顯示via出來,只希望在執行完我
寫的command file後只會出現metal1、metal2及metal3。
* Q" R( c" ~- @5 l   但我今天試了很久還是試不出來,不知道有無前輩們是否也寫過類似的
! r/ g" `8 Z) k- Y5 ?command file呢?希望能給小妹一點意見,或者有無相關data能參考...。
3 f2 z2 H! y+ L; m
- y- p7 z1 h1 `' V4 q麻煩各位前輩了~謝謝~

semico_ljj

谢谢了,实用

james65chan

VCCA_M1 { NET mt1i VCCA } DRC CHECK MAP VCCA_M1 16 0 VCCA.gds

shkao0201

試試 Net 指令
Layer operation
6 n8 t& O) j( r, oNET layer name [… name]
/ V- V2 R& ?/ C9 Q+ BParameters
• layer
# A0 P4 L: H5 J( b" K9 fA required original layer or layer set, or a derived polygon layer.
4 j, E: S9 Z5 R* b• name
0 R8 P1 G( y6 k! aA required name of a net, which can contain one or more question mark (?) characters. The
? is a wildcard character that matches zero or more characters. You can specify name any
number of times in one statement. The name can be a string variable (see Variable).
& ^; p4 x! y7 @  P$ e. C9 PDescription
5 V6 I  `3 z. F8 xSelects all layer polygons that belong to the net having the specified name. To avoid ambiguity,
3 m+ z2 r7 z5 V! p# J: q5 jyou must use the parameters in layer name order.
Note
Do not use this operation to obtain net shorting information. The Net operation uses net
6 |* s! m  e' v# `  y  y; w/ k% Anames assigned by the connectivity extractor. If the connectivity extractor encounters
shorted nets, it assumes it has found a single net, and assigns it one name.
  Y& b# c) d* _" PThe connectivity on layer must be established through a connectivity operation.
See also Not Net, Net Area, Connect, Sconnect, and Stamp.
3 ?1 x5 {  `" z. o! s4 XExamples
METAL_SP {
@ VDD metal must be spaced at 4.5 microns
5 C$ s" P, O: |/ O, K( v@ VCC metal must be spaced at 4 microns
% ^+ w0 j7 h" V: B- Cvdd_metal = metal net vdd
' b& E( k2 J" c8 n9 l. R& nvcc_metal = metal net vcc
external vdd_metal < 4.5
9 D* b4 G# i& D. T# t% bexternal vcc_metal < 4.0

camilla

各位前輩,不好意思忘記註明軟體了,我是使用calibre ,麻煩大家了

veteran

妳最好註明是哪個軟體用的Command file。這樣別人比較好幫妳..