Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:
1 T" `) u5 E; u. J2 @
# K# _" }# Y, ?* Y* B9 [7 S( \) o
- @0 S7 Q8 ^- h: H7 M7 ICould not connect to socket 9189 on host localhost
# ]6 O4 o  ~4 c, d
Probable causes:

1: The viewer is not running, or
7 `. R- Y, _- B* o3 C4 C2: The viewer's server socket is not activated

! p( Z3 F# O- x/ g
. _/ o+ D0 j+ L/ _請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
+ K9 _% T5 P0 d" ]& {所以你無法將RVE的資料傳回layout
virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
. @! P) Y* I. b, [virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

& D( Z" ?% k! f$ d. d% S0 v+ `' \" t0 i
7 L2 N) Z/ H2 d& u( d' G
- p( a( W$ X: A0 k  q+ F  L5 e9 L: I我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
' T! P" [7 p& m9 {% M                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
3 O+ p5 m# m$ d, [If you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer after invoking Calibre
6 N7 t7 c1 N7 m" X* ?Interactive, you can set up communication between the two tools through IPC sockets.
/ G6 P) Q, |2 ^1 B, q- S7 D: TBy default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
You can change the socket address used by following this procedure:
. V+ Y! U7 `0 _0 i6 o* L; x1. Open the viewer.
. N9 |/ q: ^" ?2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
1 R6 \3 s8 V9 u* ^4 C( d3. In Calibre Interactive, choose Setup > Layout Viewer…
4. Enter the socket number that you activated in the viewer.
5. Click Connect.
' C+ h- f( k% J& Q( T6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
5 y/ S' G' i2 g/ E; ~) v7 [Setting Up Communication With a Viewer
8 V1 Y! s+ j" J+ k; _6 IIf you invoke Calibre Interactive from a layout or schematic viewer, communication between
# H$ M( u. s/ _1 B* s$ [, lthe two applications is set up automatically. If you open a viewer a ...

8 @4 e" j6 n/ a* u; q7 N0 V
/ V% A% `5 N1 r& q6 d
一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
它的socket number 有相同嗎?