Chip123 科技應用創新平台

 找回密碼
 申請會員

QQ登錄

只需一步,快速開始

Login

用FB帳號登入

搜索
1 2 3 4
查看: 11588|回復: 7
打印 上一主題 下一主題

[問題求助] Calibre遇到的問題

  [複製鏈接]
跳轉到指定樓層
1#
發表於 2009-10-29 17:32:54 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式
執行calibre時,出現了這個警告:
  @" [" W- t; a" C- E5 k" V  R* p
- W% T: U8 a# P* w1 t0 t- M, Q' ?) l& w1 o) H
Could not connect to socket 9189 on host localhost, y0 j, v- A1 [6 p* I5 {
% U" ^  H4 R7 ^  V
Probable causes:) r2 L( L$ o% C1 @( k7 V6 c
; }; t  ^! i3 [; D. I# l
1: The viewer is not running, or$ U/ U% k8 {$ \
2: The viewer's server socket is not activated
, G5 Q8 R- N7 g$ a+ `! W* t. D1 T
7 m/ m" {- ?, I/ c- O  x8 @8 u9 G+ |! T/ X* b& [% q
請問有人遇過嗎?
分享到:  QQ好友和群QQ好友和群 QQ空間QQ空間 騰訊微博騰訊微博 騰訊朋友騰訊朋友
收藏收藏 分享分享 頂5 踩 分享分享
2#
發表於 2009-10-29 17:51:57 | 只看該作者
那是因為你的layout tool的port不是使用9189
1 Q4 M# _8 h2 e2 H+ d% b所以你無法將RVE的資料傳回layout
! @: U9 _/ H$ r7 B+ n; Mvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
( \9 T! l9 _- U0 s: S# s1 E% Slaker:Verify---Calibre---Integrate with RVE---Server Port--->9189
3#
 樓主| 發表於 2009-10-29 17:59:40 | 只看該作者
原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
2 s8 ?. x& j' G5 h那是因為你的layout tool的port不是使用9189
3 ?' ~2 f& Z9 F6 c' U  H% p9 w9 x所以你無法將RVE的資料傳回layout
0 H) N" P8 A5 Y4 H4 R* X1 evirtuoso:  Calibre---Setup---Socket-----Socket Number---->91891 U' l' N8 \7 S4 q; n$ d1 ?. g
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

5 P) _. A% \/ l: ?" r4 D) D
4 \3 l; {' ~, Q4 D& H; u# F# ~% E/ h
我使用的server port是9189
4#
發表於 2009-10-29 18:08:29 | 只看該作者
試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個3 c- D! {0 ^; `  B) H- R
                                                                                         ----IPC  settings--socket number-----9189
5#
發表於 2009-10-29 18:10:33 | 只看該作者
然後你可以試試點Connect是否會出現Success.
6#
發表於 2009-10-29 18:12:59 | 只看該作者
Setting Up Communication With a Viewer/ H, @9 d9 }/ k" h
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
9 b' t' f7 e" l. ]the two applications is set up automatically. If you open a viewer after invoking Calibre
3 M4 Z. _0 S/ X& A  a& KInteractive, you can set up communication between the two tools through IPC sockets./ p6 j( C9 B% l0 d. x
By default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
8 B8 Y3 a6 Y' y3 K/ z" wYou can change the socket address used by following this procedure:
& G- M5 e  H* k7 I4 r1 t$ v3 n1. Open the viewer.
9 _& {. j0 g$ L" N& h3 i3 k2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.+ c5 ?# _" |$ {9 a* p3 M9 b
3. In Calibre Interactive, choose Setup > Layout Viewer…
, d& ^9 q  \! H2 G. ~4. Enter the socket number that you activated in the viewer.
9 R9 W) E- X+ ^+ M: l5. Click Connect.
# Z( B9 N& i' p  P* p# ^( j: ?9 z6. Click OK. The figure shows setup of a layout viewer.
7#
 樓主| 發表於 2009-10-29 19:35:14 | 只看該作者
原帖由 shkao0201 於 2009-10-29 06:12 PM 發表 ) W' n& V' u% Y# k& A9 V9 z% U
Setting Up Communication With a Viewer
. B) X. O) y# P( PIf you invoke Calibre Interactive from a layout or schematic viewer, communication between: {3 ^! J/ k8 K* _! }! O" l9 J5 y
the two applications is set up automatically. If you open a viewer a ...
$ O" s$ I; D& L0 ~. T' T+ h- E! j' [

& H" j4 O( J& I+ a
' z& E7 t' ^$ i7 H6 k% \1 t一樣不行用?
8#
發表於 2009-10-30 09:51:55 | 只看該作者
你是試用laker去叫出RVE呢??
2 X* [3 p6 W# T8 \3 d8 P* G它的socket number 有相同嗎?
您需要登錄後才可以回帖 登錄 | 申請會員

本版積分規則

首頁|手機版|Chip123 科技應用創新平台 |新契機國際商機整合股份有限公司

GMT+8, 2025-2-28 09:53 AM , Processed in 0.156008 second(s), 18 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表