Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:


Could not connect to socket 9189 on host localhost

Probable causes:

1: The viewer is not running, or
2: The viewer's server socket is not activated
& b+ L0 J- B+ U& q9 R# q% u$ }' A6 u
& k- k6 n2 ~7 O* `7 R
4 O% S; x& H8 j請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
+ }/ ?' C. F8 D! H6 G& W( {virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
5 {$ b( d2 n+ Ylaker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
* k, Z. F+ p* Pvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

* `  X7 }& E& T$ u) r# S# d7 \我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
+ p2 L/ U3 h/ R* {4 D) {+ B3 e! t                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
% q$ A2 O" l. b4 b2 zIf you invoke Calibre Interactive from a layout or schematic viewer, communication between
8 u" ?; V  c  N2 Z4 {! ^; |5 _) Jthe two applications is set up automatically. If you open a viewer after invoking Calibre
Interactive, you can set up communication between the two tools through IPC sockets.
- w% {: S! M, a  f6 H/ FBy default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
8 K2 I" ~2 X% J$ `- Z6 EYou can change the socket address used by following this procedure:
! ^/ M  n7 {* n9 v1. Open the viewer.
& w) z6 Z' O0 K5 k& X2 `2 M2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
  r/ m  w0 u% k; c3. In Calibre Interactive, choose Setup > Layout Viewer…
0 P8 T1 g0 t7 k4. Enter the socket number that you activated in the viewer.
' `& l: ?" ]% i+ \* k4 H5. Click Connect.
$ s, |3 F1 R( P2 t6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
0 }, S. x' y( bthe two applications is set up automatically. If you open a viewer a ...

( v, t4 w. R" U; O8 S. e一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
它的socket number 有相同嗎?