PEX生出的3個黨要著麼用啊?

夜孤子

我是個LAYOUT新手，使用0.352p4m製程，好不容易跑過DRC LVS，但到PEX卡住了
6 u. p$ y) w6 R9 C! U5 i8 N& f3 z  g請問PEX產出的 .sp .pex .pxi要著麼用，才能用HSPICE跑POST-SIMULATION
: X7 I( Z7 O; M例如
5 z5 g" g! Z; {. h8 N3 P原始碼為：
.option post
/ G, ~. p: s2 l) ]: n" a! y2 z.protect
.lib 'mm0355v.l'tt
.unprotect

.subckt oscillator in1 out1 out2 gnd vdd
***************
.subckt INV Y A VDD GND
( G) S+ h6 Q$ `/ qMM1 Y A gnd gnd N W=0.7U L=0.7U
MM0 Y A vdd vdd P W=2.1U L=0.7U
.ENDS
******************
  ?7 a7 [& k: H0 c7 v! z' v+ YX1  OUT1   IN1 VDD GND INV
, M( W! U% _# Z$ p% x# XX2  OUT2  OUT1 VDD GND INV
2 A- A1 g6 ]9 U: {4 @  QMD1 IN1 IN1 VDD GND N W=0.7U L=0.7U
4 x+ O- \* @9 ~% O9 Z' }- G6 WMD2 GND GND IN1 GND N W=0.7U L=0.7U
.include "oscillator_pex.sp.oscillator.pxi"
: K/ }$ `+ v, O* B.ends
" S  N3 s- w4 U  m******************
Xo  in1 out1 out2 gnd vdd oscillator
) U; F) V6 s8 e, R2 ZV1 gnd        0        dc  0V
v2 vdd  0 dc  pwl(0 0 1ps 3v 1ns 3v)
.op
% @! G/ B0 J# m. U5 B4 Y+ C.tran 1uS 100mS
**********************************
) t7 \5 h5 }: y' `8 w( g6 h.end

7 X# Z# q+ U9 X$ x; JPEX產生的碼為
1 L% ~  G; O0 t& v.option post
.protect
0 N1 `1 }9 t: H7 ?+ L* i.lib 'mm0355v.l'tt
$ e6 d3 |" }8 t7 S5 U/ ~.unprotect
* i" w' T1 J! R7 R  A.TEMP 40
) {0 P0 {. g( _0 J' U, e: w.include "oscillator_pex.sp.pex"
.subckt oscillator  IN1 OUT1 VDD GND OUT2
; s* O5 ^; H* i6 ?7 `, I*
) l3 P, U5 J7 E7 O: r* out2        out2
. [: \) S  o" f, j4 e& Y  G* GND        GND
7 r7 y  M; ]; E$ l: M: \! }* VDD        VDD
/ e. S& a/ {  F3 h6 m* out1        out1
* in1        in1
6 X6 @. }; n/ V  ymX1_MM0 N_OUT1_X1_MM0_d N_IN1_X1_MM0_g N_VDD_X1_MM0_s N_VDD_X1_MM0_b PCH
+ L=7e-07 W=2.1e-06
: ^6 @  f# @) @7 [& CmX2_MM0 N_OUT2_X2_MM0_d N_OUT1_X2_MM0_g N_VDD_X2_MM0_s N_VDD_X1_MM0_b PCH
+ L=7e-07 W=2.1e-06
- g' N* p* h- {  o1 b0 {! fMD2 N_GND_MD2_d N_GND_MD2_g N_IN1_MD2_s N_GND_MD2_b NCH L=7e-07 W=7e-07
MD1 N_IN1_MD1_d N_IN1_MD1_g N_VDD_MD1_s N_GND_MD2_b NCH L=7e-07 W=7e-07
mX1_MM1 N_OUT1_X1_MM1_d N_IN1_X1_MM1_g N_GND_X1_MM1_s N_GND_MD2_b NCH L=7e-07
& C7 H6 b. E: N; n( X2 x; P* J# A+ W=7e-07
mX2_MM1 N_OUT2_X2_MM1_d N_OUT1_X2_MM1_g N_GND_X2_MM1_s N_GND_MD2_b NCH L=7e-07
1 a1 D) R5 C7 W  P$ d' `+ W=7e-07
*
.include "oscillator_pex.sp.oscillator.pxi"
*
5 X- ]. B. L" X9 C% F.ends

2 {8 ]- ]. a# \' w1 K
" h: f( Y. j6 R請問接下來要著麼改或著麼用，才能跑POST-SIMULATION

cakejoy

不知道你是否有子電路的觀念？
其實PEX轉出來後的檔案，你就視為子電路去呼叫它，並按照你平常的方式使用它即可！
! j6 e5 K6 O, n; O) b
# k& R- D1 i. L" e* S7 z舉例來說：
* |5 U/ h8 R$ ?* R- l" F你的PEX的子電路為
- b2 k1 G* O, B( l" X.subckt oscillator  IN1 OUT1 VDD GND OUT2
**
**
3 r0 L: m! h8 g( d/ y.ends
接下來再呼叫它
$ E, {& e4 F  uXO IN1 OUT1 VDD GND OUT2 oscillator
. J0 ~- a( P) {' B. y) t  w並填入你後面的測試語法即可。
- X' _, S6 n2 P. G
! F% I# X+ U" O註：記的最後要+.END

L_ju

: